Plumbing Basics: A Must for Bathtub Installation
Plumbing Basics: A Must for Bathtub Installation
Blog Article
Presented here below you might get a bunch of quality help and advice about How to Install a Bathtub.
Mounting a bath tub isn't specifically rocket science, but it does call for strong plumbing, carpentry, and also often, tiling skills. Changing an old tub with a brand-new one is likewise a moderately hard job. If the old bathtub is easily obtainable, the job can relocate rapidly; if you need to open a wall surface to remove the old tub and also position the new bath tub, the job is much harder. In either situation, the task is within a house handyman's abilities, although you will certainly need a helper to move out the old bathtub and also set in the new one. Ensure you have qualified yourself for the job as well as are comfortable attempting it. Rather than hiring a professional to take control of a halfway-completed project, it is better to take into consideration employing one prior to you start. Opportunities are you may need a specialist plumber to make tube connections.
This write-up will assist you install a brand-new bath tub in your shower room if you have actually currently acquired a brand-new tub as well as don't require to change the setup of your previous water supply pipelines.
Your tools and material list need to consist of the following:
Planning for the Installment
Firstly, the sustaining frame provided with the bath should be fitted (if required) according to the producer's directions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is very important to make sure that if the tap includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is additionally practical to fit a sustaining plate under the faucets system to stop stress on the bathtub.
Fit the adaptable faucet connectors to the bottom of both faucets using 2 nuts and also olives (occasionally provided with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet hole, and then pass the outlet via the hole in the bath. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the versatile overflow pipe to the overflow outlet. Afterwards, screw the pipe to the overflow face which should be fitted inside the bathroom. Make certain you use every one of the supplied washing machines.
Link the trap to the bottom of the waste electrical outlet on the bathtub by winding the string of the waste outlet with silicone mastic or PTFE tape, as well as screw on the trap to the outlet. Attach the bottom of the overflow tube in a comparable manner.The bath must currently be ready to be suited its last position.
Removing Old Touches
If you require to change old taps with brand-new ones as a part of your setup, then the first thing you need to do is detach the water system. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of getting rid of the existing faucets can be rather troublesome because of the restricted access that is frequently the case.
Make use of a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that connects the supply pipelines to the taps. Have a cloth prepared for the remaining water that will certainly come from the pipes. When the supply pipes have actually been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to quit the single taps from transforming during this process. When the taps have been gotten rid of, the holes in the bath/basin will have to be cleansed of any kind of old sealing compound.
Prior to moving on to fit the new taps, contrast the pipeline links on the old faucets to the brand-new taps. If the old taps are longer than the new taps, then a shank adapter is required for the new taps to fit.
Installing the Bathtub
Making use of the two wooden boards under its feet, position the bathtub in the needed position. The wood boards are useful in equally spreading the weight of the tub over the location of the boards rather than focusing all the weight onto four little points.
The following objective is to make sure that the bathtub is leveled all round. This can be achieved by checking the level as well as adjusting the feet on the bath tub up until the level checks out level.
To set up taps, fit all-time low of the outermost flexible faucet port to the suitable supply pipe by making a compression sign up with; then do the same for the various other tap.
Turn on the water system as well as inspect all joints as well as brand-new pipework for leakages and tighten them if necessary. Load the bath tub and also check the overflow outlet and the regular electrical outlet for leaks.
Lastly, deal with the bath paneling as described in the supplier's instruction manual. Tiling and also sealing around the bath tub must wait until the tub has actually been used at the very least once as this will certainly settle it into its last position.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly require a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the faucet as well as the other end offers a connection to the existent supply pipelines.
If you need to fit a monobloc, after that you will require lowering couplers, which links the 10mm pipeline of the monobloc to the typical 15mm supply pipe.
Next off, position the tap in the placing hole in the bath/basin ensuring that the washers remain in place between the faucet and also the sink. Secure the faucet in position with the manufacturer offered backnut. As soon as the faucet is firmly in position, the supply pipes can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with typical tap ports. The former type ought to be connected to the faucet finishes first, tightening up just by hand. The supply pipes can later on be linked to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Tiling Around the Bathtub
In the location where the bath fulfills the ceramic tile, it is necessary to secure the joins with a silicone rubber caulking. This is necessary as the fitting can relocate enough to fracture an inflexible seal, creating the water to pass through the wall surface in between the bathroom and the tiling, resulting in problems with moisture and feasible leaks to the ceiling below.
You can pick from a variety of coloured sealants to assimilate your components and installations. They are marketed in tubes and cartridges, as well as are capable of securing voids approximately a width of 3mm (1/8 inch). If you have a larger gap to fill, you can fill it with twists of soaked newspaper or soft rope. Keep in mind to constantly fill up the tub with water prior to sealing, to enable the movement experienced when the tub is in use. The sealant can crack relatively very early if you do not think about this activity prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use and reduce to size, are also conveniently offered on the market. It is advisable to fit the floor tiles utilizing water-resistant or water-proof adhesive and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
I recently found that blog entry on How to Install a Bathtub: Install an Acrylic Tub and Tub Surround when scouting around the search engines. Sharing is caring. Helping others is fun. We value reading our article about Tools You Need to Install a New Bathtub .
Need it done? Dial! Report this page